Will “Operations and Maintenance Specialist (O&M Specialist)” be Replaced By Robots? 🤔

85% Chance of Automation

“Operations and Maintenance Specialist (O&M Specialist)” will probably be replaced by robots.

This job is ranked #486 out of #702. A higher ranking (i.e., a lower number) means the job is less likely to be replaced.

Care to share? Click for Facebook, Twitter, LinkedIn, or XING. 👍

Job Description

Control, operate, or maintain machinery to generate electric power. Includes auxiliary equipment operators.

Job Details

The SOC (Standard Occupational Classification) code is 51-8013.00
The Mean Annual Wage in the U.S. is $ 73,800.00
The Mean Hourly Wage is $ 35.00
Currently, there are 35,010 people on this job

☝️ Information based on the reference occupation “Power Plant Operators”.

Also Known As…

Tasks for “Operations and Maintenance Specialist (O&M Specialist)”

Control power generating equipment, including boilers, turbines, generators, or reactors, using control boards or semi-automatic equipment.
Replenish electrolytes in batteries and oil in voltage transformers, and reset tripped electric relays.
Open and close valves and switches in sequence to start or shut down auxiliary units.
Inspect records or log book entries or communicate with plant personnel to assess equipment operating status.
Take regulatory action, based on readings from charts, meters and gauges, at established intervals.
Inspect thermal barrier coatings on integrated gasification combined cycle (IGCC) equipment for sintering, phase destabilization, or temperature variances to ensure compliance with standards and insulation efficiency.
Operate, control, or monitor equipment, such as acid or gas carbon dioxide removal units, carbon dioxide compressors, and pipelines, to capture, store, or transport carbon dioxide exhaust.
Adjust controls to generate specified electrical power or to regulate the flow of power between generating stations and substations.
Regulate equipment operations and conditions, such as water levels, based on instrument data or from computers.
Make adjustments or minor repairs, such as tightening leaking gland and pipe joints.
Receive outage calls and request necessary personnel during power outages or emergencies.
Operate, control, or monitor gasifiers or related equipment, such as coolers, water quenches, water gas shifts reactors, or sulfur recovery units, to produce syngas or electricity from coal.
Operate, control, or monitor integrated gasification combined cycle (IGCC) or related equipment, such as air separation units, to generate electricity from coal.
Control generator output to match the phase, frequency, or voltage of electricity supplied to panels.
Operate or maintain distributed power generation equipment, including fuel cells or microturbines, to produce energy on-site for manufacturing or other commercial purposes.
Control or maintain auxiliary equipment, such as pumps, fans, compressors, condensers, feedwater heaters, filters, or chlorinators, to supply water, fuel, lubricants, air, or auxiliary power.
Collect oil, water, or electrolyte samples for laboratory analysis.
Record and compile operational data by completing and maintaining forms, logs, or reports.
Clean, lubricate, or maintain equipment, such as generators, turbines, pumps, or compressors, to prevent failure or deterioration.
Start or stop generators, auxiliary pumping equipment, turbines, or other power plant equipment as necessary.
Examine and test electrical power distribution machinery and equipment, using testing devices.
Monitor power plant equipment and indicators to detect evidence of operating problems.
Communicate with systems operators to regulate and coordinate line voltages and transmission loads and frequencies.
Place standby emergency electrical generators on line in emergencies and monitor the temperature, output, and lubrication of the system.

Related Technology & Tools

Excitation systems
Cooling towers
Gas detectors
Turbine flow meters
Vibration monitors
Catalytic sensors
Bucket elevators
Purge pumps
Switch yard equipment
Panel boards
Annunciators
Flow meters
Grease guns
Condensers
Orifice plates
Signal converters
Circulating fluidized bed CFB boilers
Electrical switch gear
Soot blowers
Desktop computers
Pressure transmitters
Igniters
Selective non-catalytic reactors
Pulverizers
Selective catalytic reactors
Oil filters
Power transformers
Screw conveyors
Digital panel meters
Hard hats
Water heaters
Wet scrubbers
Absorbers
Screens
Gas generators
Temperature transmitters
Unit governors
Fire tube boilers
Air filtration mask
Boiler gauge glasses
Water softeners
Combustion turbines
Attemperators
Water treatment equipment
Vacuum pumps
Diesel driven generators
Steam turbines
Level transmitters
Coal dryers
Heat recovery steam generators
Flow transmitters
Steam distribution systems
Water filters
Heat pumps
Oil guns
Shell and tube heat exchangers
Motor compressors
Water pumps
Brushless direct current DC motors
Air heaters
Conductivity probes
Water gauges
Transformer controls
Dry scrubber systems
Geothermal binary turbines
Chain conveyors
Flue gas desulferization systems
Mainframe computers
Fin fan heat exchangers
Limit switches
Plate exchangers
Self-contained breathing apparatus
Belt conveyors
Steam gauges
Impact crushers
Digital readouts
Control boards
Steam driven turbogenerators
Touch screen monitors
Steam condensers
Combustion engines
Rotameters
Blowers
Analog panel meters

Microsoft Access
Microsoft Excel
Siemens Teleperm
Emerson Ovation
Microsoft Office
Computerized maintenance management system CMMS
Teknik Segala OSI Plant Information PI System
Siemens Power Plant Automation SPPA
Safety instrumented system SIS software
Gas field monitoring system software
Email software
General Electric Mark VI Integrated Control System ICS
Microsoft PowerPoint
Yokogawa FAST/TOOLS
Distributed control system DCS
Continuous emissions monitoring systems CEMS
Microsoft Word
General Electric Mark VI Distributed Control System DCS
Supervisory control and data acquisition SCADA software
Interlock shutdown systems
Microsoft Outlook